Skip to main content

Mehls Hauling & Demolition

Trusted Flooring Removal & Grinding Installer in Northeast Ohio

Mehls Hauling and Demolition handles the heavy, dirty prep work that comes before new floors go in. Whether you are pulling up ceramic tile in a kitchen, clearing broadloom glue off a basement slab, or grinding away discolored garage epoxy, our crew gets your concrete bare, flat, and clean. Flooring contractors around here prefer installing over a subfloor that has been properly prepped, because it stops glue failures, hollow tiles, and uneven seams before they happen.

What Actual Subfloor Prep Entails

Ripping up an old floor sounds simple until you hit the adhesive layers underneath. A quick carpet pull leaves behind thousands of staples and yellow glue lines. Popping off tile leaves razor-sharp ridges of thinset hardened onto concrete. New materials—especially luxury vinyl plank, wide hardwood, and large-format porcelain—demand a subfloor that is smooth within tight tolerances. If you lay new flooring over old residue or high spots in the slab, those defects telegraph right through to the surface over time.

That is where mechanical prep comes in. Mehls Hauling and Demolition brings walk-behind grinders, ride-on scrapers, and heavy HEPA dust suppression to strip materials down to solid, bare concrete across Northeast Ohio.

Keeping Tile Dust Out of Your Air Ducts

Smashed ceramic and stone tile sends fine silica dust everywhere if it isn't managed at the point of impact. We hook our breaker tools and grinders directly into pulse-jet HEPA extractors. We also mask doorways and seal HVAC returns so dust stays confined to the work zone instead of settling on your furniture or sticking inside your furnace ducts.

Shaving Down High Spots & Rough Slabs

Concrete slabs rarely dry perfectly flat. High spots create teetering planks and uneven grout lines. We run industrial diamond-head grinders across the slab to shave down concrete ridges, humps, and rough trowel marks until the subfloor meets your installer's flatness specs.

Scraping Off Old Mortar and Sticky Carpet Glue

Old thinset ridges act like cement rocks under new planks. Standard scrapers usually slide right over them or gouge into the slab. We run specialized segment heads on our machinery to grind off rock-hard mortar and soft, gummy adhesives without chewing up the structural concrete underneath.

Pulling Up Glued or Nailed Hardwood

Solid oak and engineered planks glued to concrete don't come up without a fight. Our crew uses machine scrapers to pop glued wood, pull stubborn fasteners, and clean up the sticky residue left on the substrate so the surface is ready for a fresh start.

Stripping Failed Garage & Shop Epoxies

Thick garage floor paints and failing urethanes tend to flake, peel, and discolor over time. Putting fresh epoxy over a peeling surface just means the new coat will pull right off. We mechanically scarify the floor, grinding away high-build coatings until we hit clean, virgin stone.

Getting the Base Flat Before New Material Arrives

Dip and slope problems in a concrete floor cause hollow sounds under foot and broken floor locks over time. We check subfloors with straightedges, grind down high points, patch static cracks, and apply self-leveling underlayment where deep low spots threaten your new layout.

Tack Strips, Staples, and Yellow Glue

Tearing up old carpet takes twenty minutes; getting the floor ready for vinyl or hardwood takes real work. We pull up perimeter tack strips, pull thousands of buried floor staples, and scrape off old carpet adhesive so your floor installer gets a spotless base.

High-Capacity Demo for Commercial Builds

Retail spaces, offices, and medical facilities often have tight build-out windows. We bring ride-on equipment and multi-head planetary grinders to strip thousands of square feet of VCT, carpet tile, and rubber backing quickly so your general contractor stays on schedule.

Roughing Up Slabs for Better Adhesion

Glues, epoxy systems, and self-leveling underlayment cannot stick to slick or sealed concrete. We grind and profile the slab to create a fine micro-texture—giving adhesives a physical surface to grip into so your new floor never delaminates.

Cleaning Out Laitance, Oils, and Old Sealers

Concrete often holds onto invisible contaminants like curing compounds, oil drips, and surface laitance (a weak layer of unbonded cement powder). Diamond grinding removes this top surface layer, exposing durable concrete that bonds tightly with mortars and adhesives.

Why Skipping the Prep Costs You Later

Most flooring failures have nothing to do with the flooring material itself. They happen underneath. When installers lay luxury vinyl or hardwood over uneven concrete, the planks flex every time someone walks across them. Eventually, the locking joints snap, seams open up, and planks start to squeak or bounce.

Adhesive failure works the same way. If an installer puts glue over old carpet mastic, paint, or dusty concrete, the glue bonds to the dust or old paint instead of the slab. Within a year or two, moisture or foot traffic causes the glue to release. Scraping and grinding the concrete down to raw stone gives thinset and adhesives direct access to the pores of the slab, locking the new floor down permanently.

There is also the health and mess factor. Dry-sweeping or using standard shop vacs during tile tear-out sends micro-fine silica dust into your house. That dust hangs in the air for days and coats every surface. Using commercial pulse-jet vacuums and containment walls traps dust before it escapes, saving you from spending hundreds of dollars on professional house cleaning after the demo is done.

Floor grinder and scraper removing old adhesive from a concrete slab in Northeast Ohio

How We Operate on Job Sites

Mehls Hauling and Demolition is a locally owned company that takes pride in doing dirty work the right way. We show up on time, communicate clearly, and leave job sites swept clean so your finish crew can walk right in and go to work.

15 Years Combined Experience

We have handled hundreds of tear-outs across homes, storefronts, and industrial spaces, learning how to handle tricky glues and soft concrete without damaging subfloors.

Local Ownership

We live and work in the area, building our business on honest estimates, clear timelines, and straightforward advice.

Installer-Ready Work

We don't call a job finished until the subfloor passes flatness checks, glue residue is gone, and the space is vacuumed clean.

Industrial Gear

We invest in heavy walk-behind grinders, diamond tooling, and heavy-duty dust collectors so we can handle thick coatings and stubborn mortars without dragging out the job.

Step-by-Step: What to Expect on Demo Day

Every floor project follows a set routine to protect your property and keep the job moving efficiently.

Walkthrough and Prep

We inspect the room, test floor hardness, check moisture levels, and plan out machine paths and equipment power requirements.

Containment Setup

We hang heavy plastic sheeting across open doorways, seal off cold air returns, and protect walls and adjacent trim.

Tear-Out and Grinding

Crews operate mechanical scrapers, breakers, and diamond planetary grinders to remove materials, scrape glue, and flatten high points.

Vacuuming and Debris Removal

We run high-efficiency HEPA extractors across the slab, detail corners by hand, and load all waste into our trucks for off-site disposal.

What Contractors & Homeowners Say

Here is what local property owners, flooring installers, and general contractors have to say about working with our tear-out team.

“Wow! Carter made this process so easy. From the pricing to the coordinating, they really know how to crush the competition. We’ve been having such a hard time trying to find a dumpster for yard waste only and they made it happen same day! Truly, such an amazing experience and will be using them next time”

RU
Rebekah UnderwoodGoogle Review

“These guys are super prompt and deliver exactly what they say they will deliver. My impression is these young guys are eager to make their mark in this business. Give them a call, you won’t regret it.”

BB
Ben BeckerGoogle Review

“Mehls Hauling was exceptional to work with. Extremely helpful and communicated with us perfectly. Will definitely be using them again.”

JS
JT SianoGoogle Review

5.0 from 14 Google reviews

Frequently Asked Questions

What areas do you travel to for tear-out jobs?

Mehls Hauling and Demolition serves residential and commercial clients throughout Northeast Ohio. Our mobile units bring grinding equipment, scrapers, and dust containment rigs directly to your property, whether you have a small residential bath update or a large retail renovation.

Can't I just put self-leveler or glue straight over old thinset?

Pouring self-leveling concrete or spreading new glue over loose thinset, yellow adhesive, or flaking paint is a gamble. The new material will only bond as well as the old layer beneath it. If that old thinset pops loose off the slab, your entire new floor comes up with it. Mechanical grinding opens the pores of the concrete so levelers and adhesives grip directly into the stone.

How do you stop fine concrete dust from spreading?

We connect continuous pulse-jet HEPA vacuums straight to our diamond grinders and hand shrouds. Dust gets captured right where the diamond tooling cuts into the material. We also set up plastic barrier walls and cover air vents so fine particles cannot migrate into adjacent living areas or furnace ducts.

Can diamond grinders remove old cutback glue or thick epoxy?

Yes. Soft or sticky adhesives like black cutback mastic or thick garage epoxy can gum up standard sanding pads. We use specialized polycrystalline diamond (PCD) tooling designed to cut, slice, and lift gummy sealers and high-build coatings cleanly off the concrete base without smearing adhesive back into the pores.

Do you handle large retail and office demo jobs?

We frequently work with commercial general contractors, retail managers, and property owners. Our crew manages multi-room VCT removal, commercial broadloom carpet scraping, tile demo, and full floor scarification while working around tight scheduling deadlines.

How long will my floor tear-out take?

Most residential jobs—such as a 500-square-foot basement or kitchen tile removal with light concrete grinding—take one full day. Larger projects, heavy thinset removal, or extensive subfloor leveling across multiple rooms may take two days depending on slab hardness and access points.

Can you flatten concrete that has low spots or long cracks?

We handle both high and low slab defects. High ridges are ground flat with diamond heads. Long cracks are chased out, cleaned, and filled with epoxy or polyurea repair material. For low areas or uneven slopes, we apply primer and self-leveling underlayment to create a smooth, level plane.

Who hauls away the old flooring and concrete debris?

We handle all cleanup and hauling ourselves. All pulled carpet, broken ceramic tile, wood scrap, and ground concrete dust are swept up, bagged, loaded onto our trucks, and hauled away. You won't have to hire a dump trailer or leave a heavy container sitting on your driveway.

Schedule a Site Inspection or Get an Estimate

If you are planning a floor renovation, start with a solid foundation. Mehls Hauling and Demolition offers honest assessments, clear scheduling, and thorough subfloor prep for property owners across Northeast Ohio.

Call us directly at +1 (440) 557-4285 or email info@mehlshauling.com to discuss your project and schedule an on-site estimate.

Request Your Free Estimate

HoursOpen 24 hours
Service AreaLake, Cuyahoga, Ashtabula, Geauga, Summit, Lorain & Portage counties, OH
Call +1 (440) 557-4285

Our Service Area Across Northeast Ohio